sand cone apparatus

  • 11 Soils Field Procedures Using the Sand Cone Method

    1) Fill the apparatus with the calibration sand and record the weight to the nearest 0.01 lb 2) Place the base plate on a clean, level surface 3) Invert the apparatus onto the base plate and open the valve to allow the cone and the base plate to fill with sand 4) When the sand stops flowing into the cone

    Free Chat →
  • ELE International

    Density Plate for EL29-4300. 29-4340. For 6 inch sand cone. The plate has a 6.5 inch diameter recessed hole to locate the sand cone.

    Free Chat →
  • Sand Cone Apparatus Archives

    More than 5,000 products has been listed in Tool Bazaar.pk. One of the Biggest Construction Industry Equipment Bazaar with vast variety of products defined and promoted.

    Free Chat →
  • Standard Test Method for Density and Unit Weight of Soil

    6. Apparatus 6.1 Sand-Cone Density Apparatus, consisting of the follow-ing: 6.1.1 An attachable jar or other sand container having a volume capacity in excess of that required to fill the test hole and apparatus during the test. 6.1.2 A detachable appliance consisting of a cylindrical valve with an orifice approximately1⁄2in. (13 mm) in

    Free Chat →
  • Standard Test SOILS Procedures Manual Subject DENSITY

    The weight of sand to fill the lower cone will be determined in similar manner. Place the sand cone device on a flat surface and allow the sand (5000 g) to run into the cone. The difference between the original and final weight shall be recorded as the weight of sand to fill cone. Calculate the unit weight of sand from the above determinations.

    Free Chat →
  • TEST METHOD FOR EARTHWORK COMPACTION CONTROL BY

    - On a level surface, fill the apparatus with sand through the cone at a uniform rate until sand stops. - Close the stopcock carefully and pour off the excess sand remaining in the cone. - Weigh the filled sand cone apparatus. - Invert the sand cone apparatus on the base plate on

    Free Chat →
  • Sand Cone Apparatus Set, 6.5 inch (165 mm)

    The sand cone apparatus determines the in-place density of soils having a maximum particle size of up to 2inches (51mm) using test hole volumes of approximately 0.1ft (2.8L). The set is comprised of a 1-gal. (3.79L) threaded plastic jar

    Free Chat →
  • Sand Cone Apparatus

    EI29-4302. Sand Density Cone x 1 EI29-4292/10. Replacement Sand Jug x 2 EI29-4342. Field Density Plate x 1 EI29-4355. Bags, Density Sand x 2 EI88-7700. Spoon x 1 EI88-7960. Steel Chisel x 1 EI88-7940. Rubber Mallet x 1 EI88-7300. Scoop x 1 EI88-7042. Field Cans x 12 EI88-1600 Field Scale x 1

    Free Chat →
  • Cooper Technology

    Cooper Research Technology is a British company and one of the world leaders in the design and manufacture of high performance testing equipment for civil engineering materials.The Nottingham Asphalt Tester (NAT), designed in the 1980's by our founder Keith Cooper whilst working at the University of Nottingham, was the first of its type.

    Free Chat →
  • Sand Cone Apparatus, Sand Cone Apparatus

    Alibaba offers 87 sand cone apparatus products. About 97% of these are testing equipment. A wide variety of sand cone apparatus options are available to

    Free Chat →
  • S

    The Sand Cone Apparatus is used to determine the in-place density of any soil that can be excavated to a stable condition with hand tools. This method is generally limited to materials with a maximum particle size of 2 in (5.1 cm).

    Free Chat →
  • J~

    The apparatus shall be as follows: (a) Sand Cone Assembly. - AI-gal. jar and a detachable appliance consisting of a cylindrical valve with an orifice l/2-in. in diameter and having a small funnel connecting to a standard G mason jar top on one end and a large funnel on the other end.

    Free Chat →
  • GDT 20

    GDT 20 Page 3 A B B x 100 A = weight of wet sample B = weight of dry sample 2. Determining the Volume of the Density Hole a. Weigh the sand cone apparatus and sand and record as gross weight of sand, cone, and jar.

    Free Chat →
  • Sand Cone Apparatus 6 1/2

    The Sand Cone Density Apparatus determines the in-place density of soils. Unit consists of a one gallon threaded plastic jar and a 6 1/2 detachable cone. Cone consists of a brass cylindrical valve with a 1/2 diameter orifice with built-in stops to prevent rotation past completely open or completely closed positions.

    Free Chat →
  • (DOC) Lab soil, exp # 6

    Objective : To check the compacted dry unit of soil and compare it with the specification drawn up for the construction . Apparatus : 1- Sand cone apparatus. 2- Base plate. 3- One gallon can with cap. 4- Tools to dig a small hole in the field. 5- Balance. 6- 20-30 Ottawa sand.

    Free Chat →
  • AASHTO T 191 – DENSITY IN

    For each container/bag of sand there will be a unique cone correction and sand calibration factor. Each sand-cone and matched base plate will also have a set of unique cone corrections and bulk sand densities. If more than one sand-cone apparatus is available, the sand-cone and base plate should

    Free Chat →
  • ARCHIVE

    MT 222-04 (11/10/04) 3 of 5 4 Cone Correction and Bulk Density Factors: 4.1 Filling the apparatus: . 4.1.1 Place the empty apparatus upright on a firm level surface, close the valve and fill the funnel with sand.. 4.1.2 Open the valve and keep the funnel at least half full with sand during filling. When the sand stops flowing into the apparatus, close the valve sharply and empty the excess

    Free Chat →
  • PROJECT METHODE: Sand Cone

    Aug 04, 2010Sand cone apparatus which consists of a one-gallon plastic bottle with a metal cone attached to it. One-Gallon plastic can with cap. Balance sensitive to 1 g. Base plate ; Tools for excavating a hole in the ground ; Clean, uniformly graded sand ranging from #20 to #30 sieve such as Ottawa Sand

    Free Chat →
  • Sand Density Cone Apparatus

    Sand Density Cone Apparatus. Make: LabTek. Model: SL-2060. Origin: India. Standards: ASTM D1556 | AASHTO T191 | NF P94-061-3 Specification: The verification of the degree of compaction can be determinate on site by a simple procedure consisting essentially in removing and weighing a part of compacted soil and replacing in the hole with sand by a simple apparatus recording the volume of sand

    Free Chat →
  • Field Density Test Of Soil By Sand Cone Method

    Dec 26, 2016The sand cone method is one of the most common methods that are used for field density test in highway construction to check the compaction of soil layers. The sand cone method is one of the most common methods that are used for field density test in highway construction to check the compaction of soil layers. Menu.

    Free Chat →
  • Standard Test Method for Density and Unit Weight of Soil

    scope: This test method may be used to determine the in-place density and unit weight of soils using a sand cone apparatus. This test method is applicable for soils without appreciable amounts of rock or coarse materials in excess of 11⁄2 in. [38 mm] in diameter.

    Free Chat →
  • DETERMINATION OF FIELD DENSITY OF SOIL BY SAND

    Apr 02, 2014Aim To determine the field density of soil at a given location by sand replacement method Reference IS-2720-Part-28-Determination of dry density of soils in place, by the sand replacement method Apparatus Sand pouring cylinder Calibrating can Metal tray with a central hole Dry sand (passing through 600 micron sieve) Balance Moisture content bins Glass plate []

    Free Chat →
  • sand patch apparatus

    sand patch apparatus. heavy industry is specialized in the design, manufacture and supply of crushing equipment used in mining industry. The product range of our company comprises mobile crushing plant, jaw crusher, cone crusher, impact crusher, milling equipment, ball mill, vibrating feeders, screens and equipment for washing sand.

    Free Chat →
  • ARCHIVE

    MT 222-04 (11/10/04) 3 of 5 4 Cone Correction and Bulk Density Factors: 4.1 Filling the apparatus: . 4.1.1 Place the empty apparatus upright on a firm level surface, close the valve and fill the funnel with sand.. 4.1.2 Open the valve and keep the funnel at least half full with sand during filling. When the sand stops flowing into the apparatus, close the valve sharply and empty the excess

    Free Chat →
  • Sand Cone Density Apparatus (6

    HM-100 Sand Cone Density Apparatus (6-1/2in) is a 1gal (3.8L) threaded plastic jar with detachable metal double cone fitting. The cone is threaded on one end, flanged to 6-1/2in (165mm) on the other, with a cylindrical valve of 1/2in (12.7mm) Dia. orifice between ends.

    Free Chat →
  • Standard Test Method for Density and Unit Weight of Soil

    scope: This test method may be used to determine the in-place density and unit weight of soils using a sand cone apparatus. This test method is applicable for soils without appreciable amounts of rock or coarse materials in excess of 11⁄2 in. [38 mm] in diameter.

    Free Chat →
  • Get Price And Support

    Simply complete the form below, click submit, you will get the price list and a Hmard representative will contact you within one business day. Please also feel free to contact us by email or phone. ( * Denotes a required field).